cortina Tag Posts Index

Hice las cortinas para la cocina 😃🥳 (Es/En)

Feliz tarde mis queridos amigos de Hive, cómo de costumbre les envío un cálido saludo y un genuino deseo de que cada uno de ustedes se encuentre bien. Con alegría

Flight of the Unbreakable - OpenSea Rarible NFT Symphonic Metal Music Song

🎵 Today's fresh tune on One Hit A Day is: Flight of the Unbreakable 📅 Date Created: February 8, 2026 👨‍🎨 Artist: DJ Dufreezy (aka DJD) 🌐 Language: English ℹ️

A Daily Word in Spanish (#208)

Blog de @aljif7 PLATAFORMA: Hive FECHA: Viernes 31 de octubre de 2025. Área: Educación-Aprendizaje. A Daily Word in Spanish (#208)- Cortina (la) (Sources: Educalingo,

ENG / ESP Three dimensional flower made with cardboard. / Flor tridimensional hecha con cartulina.

Paper flower curtain for a Hawaiian party.Cortina de flores de papel para fiesta Hawaiana. This Saturday was my daughter Rafaella's sixth birthday. I spent several

Welding back the scuttle

With everything having a generous, dry coat of paint, I put seam sealer along all the edges that needed it, similar to how the factory had it. I also cut out the

Closing the first layer up on the scuttle

With the rust cut out and surrounding metal treated, I got to work welding in ptches of metal. I learnt my lesson on the previous side, where I had tried to create

Open up the left hand side of the scuttle, a rusty surprise!

Spurred on by the feeling of accomplishment of finishing up the left hand side door frame I moved to the right hand side, starting with the scuttle. From the outset

Finishing up the left hand door opening

With the scuttle welded back in place I could proceed with closing up all the last of the places where I had cut rust out around the door frame. First a piece was

Finally closing up the scuttle panel

After quite a long time, my last post was in May, I got to closing up the scuttle panel in December of 2024. I made use of plastic tile levellers to hold the piece

Using plumbing supplies on a car

My hair brained scheme to route whatever water leaks behind the windscreen rubber out may work, or not, time will tell. I am definitely not ready to solder plumbing

Welding the repair panel in

After much back and forth, test fitting and finally some paint, the bottom has a decent coat on, I managed to get something welded in place. I still had to tweak

Patching a small hole in preparation for welding the replacement part in

I had some small details to finish before welding in the patch under the windscreen cowl. There was a tiny hole to patch and I marked the places where the holes

Using tiling tools to hold a part in place

As is probably expected the part I cut out warped a bit and does not fit back in position perfectly. I picked up some of these, they are meant for leveling tiles,

Refining the patch panel for under the windscreen

With the rough shape I started refining it until finally I could get the piece I cut out to fit over it. It took quite a bit of back and forth, offering the two

Getting a rough shape for the replacement panel under the windscreen

I pondered a long on time on how to get started with this piece. Eventually I just took the bits I had cut out and used them as a guide and cut a section of plate

A lot of work for little visual difference

Not an lot of change visually but I did spent quite some time welding in thin strips to replace the rusted edges that I had cut off / back to get to clean metal.

Starting to patch up the rust under the windscreen

Cutting out rust from the inner layer meant I could now see through and into the cab... I chased down the last bit of rust into the engine bay as well and made up

Peeling away another layer to find even more rust

I tried cutting away the least amount of metal, so that replacing it would be somewhat simple, unfortunately I found more rust after I cut the first piece out, so

Cutting out some a portion of the windshield cowl and inspecting the inside

It took a while but I finally managed to gather up the courage to cut a large hole in what, on the surface, looks to be good steel. It's actually not as bad as I

Cutting out a small part of the windshield cowl

It was quite obvious that there was rust on the edge of the windshield, so I cut out a small section to see what I might have to deal with. After a lot of